ASTM A666-10 PDF

ASTM A – Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar. This standard is a part of ASTM. ASTM A March 10, Standard Specification for Annealed or Cold- Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar. This specification. ASTM A – Designation: A – 10 Standard Speci?cation for Annealed or Cold-Worked Austenitic.

Author: Shaktikazahn Moramar
Country: Honduras
Language: English (Spanish)
Genre: Spiritual
Published (Last): 20 August 2014
Pages: 119
PDF File Size: 17.38 Mb
ePub File Size: 10.55 Mb
ISBN: 340-8-62849-638-8
Downloads: 49502
Price: Free* [*Free Regsitration Required]
Uploader: Tezilkree

Types and L provides corrosion resistance aztm a wide range of moderately oxidizing and reducing conditions, fresh water and non-marine applications.

Users of this standard are expressly advised that adtm of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. If filler metal is required, Type is normally used. Due to the high work hardening rate of these materials, intermediate a666-0 maybe required to successfully fabricate the part.

Originally approved in If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. In case of dispute, the offset method of determining yield strength shall be used.

304 and 304L Stainless Steel

Annealed Types and L can be fabricated by roll forming, deep drawing, bending and most other fabrication techniques. These alloys represent an excellent combination of corrosion resistance and fabricability. Heat to o F to o F and cool at sufficiently high rates through oF to oF to avoid precipitation of chromium carbides. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.

  74LS390 DATASHEET PDF

In the annealed condition it is essentially non-magnetic and becomes slightly magnetic with the application of cold work. B Type is generally produced with a chemical composition balanced for rich side Type or lean side Type austenite stability depending on the properties required for speci? C Annealed material that naturally meets mechanical properties may be applied. Type L Stainless Steel is preferred in welding applications to exclude the formation of chromium carbides during cooling in the heat affected region of the weld.

Find out what NKS can do for you. A — 10 Standard Speci? One bend test shall be made from sstm end of each coil. Type L LN D PSS means plate, strip, sheet. Only annealed conditions of grades speci? HardC Elongation in 2 in. The values obtained in this manner should not, however, be taken as the actual yield strength for 0.

Chemical equipment and piping, heat exchanger components, dairy and food handling equipment and utensils, cryogenic vessels and components, architectural and structural applications exposed to non-marine atmospheres.

Types and L are weldable by most fusion or resistance welding techniques. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you a666-100 attend.

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Maximum unless otherwise indicated. Permission rights to photocopy the standard may also be secured from the ASTM website www.

The choice of test method for materials in conditions other than annealed shall be at the option of the seller. Material Test Report and Certi?

This revision of Speci? Chemical equipment and piping, heat exchanger components, dairy and food handling equipment and utensils, cryogenic vessels and components, architectural and structural applications exposed to non-marine atmospheres Chemical Composition: This standard has been approved for use by agencies of the Department of Defense. However, in the case of dispute, tests shall be made by pressure.

  ANSI A208.2 PDF

ASTM A for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar

The values given in parentheses are for information only. Number of Tests 8. Types and L cannot be hardened by thermal treatment. A number in parentheses indicates the year of last reapproval. A666-10 comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.

The noncontrolling factor normally will exceed considerably the speci? Hard Elongation in 2 in.

HRC typical L Ann 25 min. Last previous edition sstm in as A — Type L should be used in heavier sections to reduce the occurrence of carbide precipitation in the heat affected region adjacent to the weld pool Corrosion: Rockwell B 95 95 Type L should be used in heavier sections to reduce the occurrence of carbide precipitation in the heat affected region adjacent to the weld pool.

and L Stainless Steel – NKS

Depending on the work hardening characteristics of the particular grade, either the yield or the tensile strength can be the controlling factor in meeting the properties. Specimens shall be bent around a diameter equal to the product of the bend factor times the speci?

Current edition approved Sept.