ASTM D1622 PDF

GeoTesting Express is a provider of Geosynthetic Testing Services – ASTM D,Standard Test Method for Apparent Density of Rigid Cellular Plastics. View Abstract. Product Details. Detail Summary. View all details. Superseded By: ASTM D/DM. EN. Format. Details. Price (USD). PDF. ASTM D – Designation: D – 08 Standard Test Method for Apparent Density of Rigid.

Author: Shakadal Shakabei
Country: Benin
Language: English (Spanish)
Genre: Automotive
Published (Last): 24 May 2004
Pages: 230
PDF File Size: 7.49 Mb
ePub File Size: 19.1 Mb
ISBN: 629-6-84044-926-1
Downloads: 90404
Price: Free* [*Free Regsitration Required]
Uploader: Meztikasa

After a minimum of 5 min, spray apply a second layer of 3.

ASTM D – 08 Standard Test Method for Apparent Density of Rigid Cellular Plastics

Note 1 — This test method is equivalent to ISO Measure all dimensions to a precision of If there are no relevant ASTM material speci? Hold the pressure of the dial aztm to 2. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

For calculation of core density, remove the bottom layer and the top skin. A number in parentheses indicates the year of last reapproval. In general, three measurements shall be made of each dimension. Revised Average value for Material 3 in Table 2.

Revised Material 4 repeatability interval, Ir. When a sliding caliper gage is used, the proper setting shall be that point at which the measuring faces of the gage contact the surfaces of the specimen without compressing them. In these cases the pressure shall be reduced accordingly. For each material, all the samples were prepared at one source, but the individual specimens were prepared at the laboratories that tested them.

  DAVID SEDARIS THE LEARNING CURVE PDF

Each laboratory obtained one test result for each material. Last previous edition approved in as D – Do not use a steel rule for dimensions less than 25 mm 1 in. A lesser number may be made when the following conditions apply: ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.

If the material does not have forming skins, the term overall density is not applicable.

ASTM D Densimeter for Plastic Measurement

Users of this test method should apply astj principles outlined in Practice E to generate data speci? Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.

Any test specimen preparation, conditioning, dimensions, or testing parameters, or combination thereof, covered in the relevant ASTM materials speci? The principles of Historical Version s – view previous versions of standard. There are no recognized standards on which to base an estimate of bias for this test method. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Measurements per Dimension 1 2 SR is the between-laboratories standard deviation of the average.

If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. April 1, 1 Added new 1. Any test specimen preparation, conditioning, dimensions, or testing parameters, or combination thereof, covered in the relevant ASTM materials specification shall take precedence over those mentioned in this test method.

  EBERRON CAMPAIGN SETTING SCRIBD PDF

Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. Users of this standard atm expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

Number of Specimens 8. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Each test result was the average of?

Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

Active Risk Management

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Spray apply a minimum 1.

D1262 specimens shall be taken from locations distributed throughout the sample. This standard has been approved for use by agencies of the Department of Defense. Combining values from the two systems may result in non-conformance with the standard.

Density can be evaluated as the apparent overall density includes forming skins or by apparent core density forming skins removed. For calculation of the apparent overall density, cut a specimen that includes the forming skin. Work Item s – proposed revisions of this standard.

If there are no relevant ASTM material specifications, then ast default conditions in this method apply.