ASTM DENGL I 0b3b | This standard is issued under the fixed designation D ; the number immediately following the. This standard is issued under the fixed designation D ; the number immediately 1 This test method is under the jurisdiction of ASTM Committee D10 on. The ASTM-D standard test method for drop test of loaded containers evaluates the capability of a container to withstand the sudden shock resulting from a.
|Published (Last):||7 July 2011|
|PDF File Size:||8.72 Mb|
|ePub File Size:||6.88 Mb|
|Price:||Free* [*Free Regsitration Required]|
If the x5276 does not protect the products well enough, damage during transport may occur. It is common to estimate the critical drop height as the midpoint between the last successful test and the test which caused damage; use of the successful test point before failure may be considered a more conservative estimate.
NOTE 1—Grout a thin mortar used to?
The drop height increment is a constant and should be between 1? ASTM D standar The height of each drop is thus determined by the result of the previous test. Repeat the drop or drop cycle on the same package until the prede? This test method may also permit observation of the progressive failure of a container and the damage to its contents.
Sometimes the drop height, test cycles, and detailed procedures are prescribed in a contract, regulation, or some other standard.
Research Report D10— describes an interlaboratory test program of three packaged items, establishing drop heights to failure.
ASTM-D – Medical Package Testing
See Practice D for additional guidance. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. Last previous edition D — Typical types of drop cycles atm as follows: If the dropping surface is a steel plate, it must be at least 1? The number of test specimens depends on the purpose of the tests but will usually require eleven or more replicate test specimens; using much larger sample sizes will wstm in higher con?
Quality Alerts View All. ASTM-D Standard Test Method for Drop Test of Loaded Containers by Free Fall The ASTM-D standard test method for drop test of loaded containers d52276 the capability of a container to withstand the sudden shock resulting from a free fall, or the capability of a container and its inner packing to protect its contents during the sudden shock resulting from a free fall. Your comments are invited asttm for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.
If it fails, the next test will be a lower drop height. Neither the depth nor width of the mass shall be less than half the length.
Drop test of loaded containers (cartons), ASTM D | AQF
Historical Version s – view previous versions of c5276. Your email address will not be published. Product inspection in Hangzhou during the G20 summit. The repeatability within laboratory standard deviation ranged from 3 to 10 in. These ISO standards may describe procedures that do not meet the requirements for this test method.
Referenced Documents purchase separately The documents listed below are referenced within the asfm standard but are not provided as part of the standard. This test method may also be used to compare the performance of different package designs. Accelerometers or other indicating mechanisms may be installed.
This test method may also be used to compare the performance of different package designs.
A number in parentheses indicates the year of last reapproval. If this specimen passes at this drop height, the next test will be at a higher drop height with a new package. Get to know us! The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. See Practice D for additional guidance.
We can help you avoid product recalls and production delays. Experience has shown that the observed precision is highly dependent on the particular packaged item being tested. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. Suppliers rejection of the drop test of loaded containers Many supplier refuse to perform a carton drop test during inspections.
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Originally published as D — Practice E is recommended. Title 49 —Transportation 49 CFR 4 3. The determination of the critical orientation must be provided.
Replicate samples should be subjected to identical procedues to determine the consistency of the failure point. Work Item s – proposed revisions of this standard.
Drop test of loaded containers (cartons), ASTM D5276
ASTM D — 98 d526 a standard test method for drop test of loaded containers cartons by free fall. It may be a formal study of the relationship between drop orientation and damage, other engineering analyses of that product and package, or laboratory and? Download our Quality Control Essentials Download.