THERMAL INSULATION OF PIPING. (WITH AMENDMENTS / SUPPLEMENTS. TO THE CINI HANDBOOK). Document nr.: PIP – This specification has. atta&ible with thermal insulation in building wall and piping . This handbook of thermal insulation applications vas prepared by EM4C. ducts and steam pipe systems with operating temperatures that are constantly above °C. CINI Manual “Insulation for industries”. CINI recommends applying .
|Published (Last):||3 June 2005|
|PDF File Size:||13.31 Mb|
|ePub File Size:||8.6 Mb|
|Price:||Free* [*Free Regsitration Required]|
Part VI contains innsulation with diagrams, tables and drawings. The software shall comply with the information given in CINI and related standards. Our expert More information.
handbbook Supply and install all materials and accoutrements required for the installation. Neither the whole nor any part of this document may be reproduced, stored in any retrieval system or transmitted in any form or by any means electronic, mechanical, reprographic, recording or otherwise without the prior written consent of the copyright owners.
The maximum stresses in the foam shall be limited to 0. Other primary vapour barriers and jacketing systems shall have the approval of the Principal. Each line should be insulated separately; a common insulation cover should not enclose adjacent lines. Once-through cooling needs large natural bodies of water More information.
Cini :: CINI manual “Insulation in Industry”
The Insulation Contractor is the party that carries out the insulation works, including engineering, material supply, installation and quality control. This is a general specification guide, intended to be used by experienced construction professionals, in conjunction with good construction practice and professional judgment. Cory Wilkerson 1 years ago Views: Improper selection and installation account for. Insulation materials shall be free of asbestos.
Where appropriate they are based on, or reference is made to, international, regional, national and industry standards. Basic premixed chemicals for in-situ moulded foam shall be produced freshly and used within the Manufacturer’s advised shelf life of the product, taking into account all transportation and storage time spans.
Specification for precast concrete blocks Part 5: Method c is normally used for tank walls ref. The top metal sheet shall overlap the bottom metal sheet and the top part of the EPDM foil shall overlap the bottom part and shall be bonded together. To reduce heat losses, insulation applied in two or more layers shall have staggered joints. Technical and industrial insulation. Improper selection and installation account for More information. Removable hot insulation around flanges, valves, etc.
Its total thickness shall be as close as possible to the economic insulation thickness and shall be rounded off to the upper commercially available thickness. A sealing plate shall ciji fitted around all protruding parts with sealed seams in accordance with Appendix 8.
TICP programs shall be used to determine the economic insulation thickness.
The input data shall be used in conjunction with software e. All materials More information.
THERMAL INSULATION (AMENDMENTS/SUPPLEMENTS TO THE CINI HANDBOOK) – PDF
All of these questions will be answered. Rail and bracket system. Embedded Parts Introduction – Anchors In the plant construction or process plants such as chemical, petrochemical, gas or power plants various disciplines are brought into contact and built on each other.
Pipes laid in the ground must be introduced into concrete walls or shafts. The metal jacket mould shall be installed with overlaps of at least 50 mm over the preformed spacers with temporary bands; vapour barrier jacketing shall be installed with bands and with all joints and overlaps sealed.
Flanges, gaskets, bolting Valves Associations involved in generating Codes for piping Design Engineering: They support petrochemical plant, More information. The responsibility of the engineer is More information. All work specified in this Section is subject to the provisions of Section The word should indicates a recommendation. The CINI Manual provides the minimum requirements to achieve optimal insulation by a correct design and application of insulation systems, listing several materials and the associated installation and finishing instructions.
High quality pipe insulation. Since a large insulation thickness may result in considerable extra capital costs for pipe bridges, civil work, etc.
Tentative sizes must be allocated to each structural More information. White Paper June 24, Stilling Well Recommendations This document describes general requirements for stilling wells used for radar tank gauging applications.
The emissivity of these materials is typically 0. The work covered under this section consists of the furnishing of all necessary labor, supervision, materials, equipment, and services to completely execute the.
THERMAL INSULATION (AMENDMENTS/SUPPLEMENTS TO THE CINI HANDBOOK)
If metal jacketing is used, sufficient space and drainage shall be provided to avoid internal accumulation of water caused by condensation, water vapour diffusion, capillary action and water ingress. Fixed costs, such insjlation scaffolding and metal surface ijsulation cost, shall not be included. The protection shall be restricted to a distance of not more than mm horizontally from access walkways and normal working areas.
For smaller pipe diameters metal jacketing is not recommended. The layer thickness shall be identical to the line insulation and shall be staggered see Appendix