EPEC 2024 PDF

Epec CAN Module Family CONTROL MODULE G08 / MAN DOCUMENT VERSION HISTORY Date Notes Document . Epec provides software tools for control system programming, adjusting, and testing. From the systems engineering viewpoint, it is not enough to have sufficient. Open and compatible. Embedded control systems are based on PLCopen and CANopenĀ®, which make them easily scalable to meet requirements for both.

Author: Feshakar Zulkiktilar
Country: Syria
Language: English (Spanish)
Genre: Literature
Published (Last): 5 June 2018
Pages: 26
PDF File Size: 8.62 Mb
ePub File Size: 16.83 Mb
ISBN: 377-9-50927-841-8
Downloads: 61312
Price: Free* [*Free Regsitration Required]
Uploader: Dutaxe

Powder-painted, hexavalent chromium free passivation for aluminium? Closed light cast aluminium housing? With input voltages below 4,3 V it seems like the internal input resistance was connected to a 1,3 V voltage source Note 2: The application program is provided with frequency and number of the pulses seen in the input in addition to the normal input state.

CANopen for all physical buses? The Color display needs extra facilities in order to have the class B covered. Maximum pulse input frequency 40 kHz. This product is not field serviceable, so it should not be opened at any situation.

Epec Control Module, Epec Control Module Suppliers and Manufacturers at

Pins of this kind can be used as e. The Mini module and the Mini display need the Hub module in order to have the full transient immunity.

Monitoring the state of the pin is generally not possible when the pin epe used as a PWM signal output. There are, for example, outputs which source current and outputs which sink current.

  8055 MICROPROCESSOR PDF

EPEC 2024 controller Manual

Recommended operating voltage 24 VDC? They can be used as high impedance voltage inputs for signals from 0 to 5 peec or low impedance current inputs for signals from 0 to 22,7 milliamperes. Some of the inputs are eepec The buyer shall compensate the manufacturer to the extent that the manufacturer might be liable to pay damages as a result of claims based on product liability according to paragraph above.

For example, if group two is configured as a current input, then both pins X3. Programming environment CoDeSys 2. The shutdown circuit is activated when voltage reaches circa 32 V.

The first is a bit variable in the IX area just in the same way as with the pins without the PI features. This epfc the normal way to connect loads when load current measurement is desired.

The system should be designed and constructed according to the Epec general mounting and cabling instruction document. Open loads can not be detected because the internal load resistor is connected to the ground.

Even if some of the inputs were not used for frequency rpec or pulse counting, these conditions must nevertheless be respected regarding those inputs too. The setting is done by a PWM channel but setting the frequency of one channel sets also the frequencies of all the other channels in the same groups. The manufacturer does not assume any responsibility for this product being fit for any particular application, unless otherwise expressly stated in writing by the manufacturer.

  CATIA DMU SPACE ANALYSIS PDF

Protection for plugs depends on cable processing?

Violating this rating may lead to system not recognizing all input state transitions Note 2: However, one or more of them can go beyond eped tolerance. Box FIN Sein? Violating this rating may lead to system not recognizing all input state transitions Note 3: Pins of this kind are used to measure analog signals.

Applies to inputs used as normal digital inputs. Generally, it is not recommended.

Pulse counting, if needed, must be enabled explicitly by the application program. Epec Oy reserves a right to improve its products without a further notice. There are two bit variables associated with each pin of this type in PLCopen programming environment.

Nominal supply voltage 24 VDC? Also the environmental suitability of equipment should be checked protection for moisture, mechanical stability, power durability, coupling resistance, among other things? All applied cables should be properly shielded, bundled and grounded?

Memory functions shall remain class A.