FLUKE PM3082 PDF

I found from a dismantled lab sell a Fluke PM I never heard anything about Fluke analog scopes. plus the name looks like a Philips. Find great deals for Fluke PM Analog Oscilloscope. FLUKE PM , PM , PM, PM ANALOG OSCILLOSCOPE SERVICE MANUAL. Find great deals for Fluke PM Oscilloscope 4 Channels mhz No Cable. Shop with confidence on eBay!.

Author: Akizuru Tausar
Country: Pakistan
Language: English (Spanish)
Genre: History
Published (Last): 10 July 2018
Pages: 385
PDF File Size: 13.29 Mb
ePub File Size: 7.75 Mb
ISBN: 280-7-82342-448-5
Downloads: 36253
Price: Free* [*Free Regsitration Required]
Uploader: Tygokazahn

The trigger sensitivity depends on the amplitude and frequency of the trigger signal. Configuration of mmicroprocessor control part Verify that a horizontal line of 4. See also section 9.

Oscilloscope MHz PM Equipment Fluke; Eindhoven

When ready, the oscilloscope is fine tuned to optimal accuracy. Synchronization is achieved via SCL. Control of the illumination amplifier V takes place by fulke of the signal DAC2, level about 1.

Page DC coupled mode. When instrument is switched off or during mains failure. After having opened the instrument, the voltage can be measured with a voltmeter or oscilloscope. To print the manual completely, please, download it.

DTB jitter in starts 1 part of 2. Refer to chapter 8. The linearity of the vertical fluek is checked by moving a signal with a fixed amplitude vertically over the entire screen area. Before turning on the instrument, ensure that it has been installed in accordance with the Installation Instructions, outlined in Section 2 of the Operation Guide.

  JOHN SCOFIELD BUMP PDF

If errors are mentioned, the oscilloscope will need corrective maintenance. The unit A1 description is split into the following chapters: Page Verify that the delay difference between the two displayed signals flue less than 0.

Differences between these models are the lfuke bandwidth, the features of the vertical channels 3 and 4 and the presence of switcheable 50Q input impedance. Use a 50Q termination. CHIP It is also possible that the rotor makes no contact. For instruments with switchable input impedance it is recommended to make use of this feature. Servicing described in this manual is to be done only by qualified service personnel.

Comments to this Manuals Your Name. TV pattern generator with video output PM test set-up: Page The linearity of the vertical amplifier is checked by moving a signal with a fixed amplitude vertically over the entire screen area.

The other IC D is the peak- peak detector for the trigger level. Before purchasing or ordering replacement parts, check the parts list for value, tolerance, rating and description.

Fluke PM3084 Analog Oscilloscope

CHIP C This diagram shows the Y-output amplifier. As input signals are used the output signals at pin 7 and 3 of N Apparatus should be properly grounded through the protective ground conductor of the power cord. Got it, continue to print. Item Om3082 code Description Earth contact Front frame CRT frontrubber Light pm30822 Page 42 – Introduction This manual also for: If working on the unit under live condition cannot be avoided, it must be done by a qualified technician who is aware of the dangers involved.

  GENIET DELPHI DEEL 1 PDF

Theseservicing instructions are for use by qualified personnel only.

Oscilloscope 100 MHz PM3082

On the power supply unit there are many parts that carry dangerous high voltages. It can function on a wide range of LINE input voltages. Flhke Time Base Description. Press the CAL key for fkuke few seconds to start the autocal procedure. The input signal is a current and is applied to V and V On this unit there are parts that carry dangerous high voltages In this test, the values of frequency and voltage are checked. Impaired Safety-protection Components which are important for the safety of the instrument may only be replaced by components obtained through your local FLUKE organisation.

There are 4 vertical channels that are mainly identical.