IRFP450A DATASHEET PDF

IRFPA Transistor Datasheet, IRFPA Equivalent, PDF Data Sheets. MOSFET. Parameters and Characteristics. Electronic Component Catalog. SRev. A, Jun 1. Power MOSFET. IRFPA, SiHFPA. Vishay Siliconix. FEATURES. • Low Gate Charge Qg Results in. Vishay IRFPA MOSFET are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for Vishay IRFPA MOSFET.

Author: Nikot Mumuro
Country: Mayotte
Language: English (Spanish)
Genre: Medical
Published (Last): 8 July 2006
Pages: 460
PDF File Size: 11.88 Mb
ePub File Size: 20.51 Mb
ISBN: 827-2-95926-792-3
Downloads: 71914
Price: Free* [*Free Regsitration Required]
Uploader: Kagagami

Potentiometer Questions Started by norbss Yesterday at You need to know what affect other parameters may have on your circuit. My circuit is 15 volts. Not as easy as it sounds.

IRFPA (IRF) PDF技术资料下载 IRFPA 供应信息 IC Datasheet 数据表 (2/8 页)

Datasheets, Manuals or Parts. Electrolytic caps are a prime suspect. Media New media New comments Search media. Click here to register now. Tc is case temperature, not ambient.

Don’t forget to check the caps. Misterbenn Active Member Mar 1, Otherwise you’ll need to resort to cold water or refrigerated cooling.

Datasheet «IRFP450A»

I am using four amp mosfets. There is also a visible crack in the case of the same Mosfet. I am assuming these are too light for the duty they are trying to perform and would like to try and replace them with heavier Mosfets. Give them a good look, especially those close to the hot heat sink. If the impedance gain or resistance gain is too high, you need more stages of MOSFET buffering to prevent overloading the gate resistors due to Qgs charge switch losses and switch frequency.

  ADMINS 30BETA PDF

Forums New posts Search forums. Lets take that number down to the graph at Figure 4. As Tony points out, there will usually be some other parameter that changes along the way.

One of the pair of Pin 11 which the burned resistor connects to has a very low resistance to ground compared to pin This is the datasheet I used for this discussion.

If so, can you suggest some part numbers? Let’s look at a few items from the datasheet. Articles Top Articles Search resources. So it will only handle 14 amps continuous if the case is kept at 25C all of the time. The unit is relatively new and hasn’t seen much use. That’s way too low as this power supply is powered by VAC which is fed through a bridge rectifier, then filtered with an uF V capacitor then fed to the Mosfets through the SMPS transformer.

IRFPA Datasheet(PDF) – International Rectifier

The sum of the junction to case and the case to sink resistances datashewt 0. Ken1 Member Feb 28, You must log in or register to reply here.

I am assuming these are too light for the duty. Replacing a 4 pin leaded inductor with a 2 pin Started by gkmaia Yesterday at The unit belongs to a neighbour and he said it just quit working; he doesn’t know if it was running hot before it quit. I am attempting to repair a Powermax PM power supply unit. Nice power supply by the way. If the case is at 25C, the junction is at 94C.

  BT137 600E DATASHEET PDF

But if increased current capacity is your only goal, there is a big trap you need to look out for. The battery charge may not have intelligent soft start and overstress the charger hooking up to a dead battery.

It seems this “entry level” charger” has very little margin before exceeding the component limits. For a better experience, please enable JavaScript in your irfp4550a before proceeding. Pins 11 and 14 are the 2 outputs of the chip. We need to recalculate everything again based on the new info. Replacement Transformer Started by ncag Today at 7: This means that the the junction is.

By continuing to use this site, you are consenting to our use of cookies. One important fact that everyone need to be aware of when choosing mosfets, is that the current irf4p50a has a fine print disclaimer that causes problems if not taken into account. You haven’t said what how you are using the mosfet, so it’s difficult to accurately answer your question.

Maybe a little overkill but, other than the copper plates that carry the current, there is no heatsink.