ISL6236 DATASHEET PDF

ISL datasheet, ISL circuit, ISL data sheet: INTERSIL – High- Efficiency, Quad-Output, Main Power Supply Controllers for Notebook Computers . ISL Datasheet, ISL PDF, ISL Data sheet, ISL manual, ISL pdf, ISL, datenblatt, Electronics ISL, alldatasheet, free, datasheet. Renesas Electronics ISL are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for Renesas Electronics ISL

Author: Dusida Arakus
Country: Zambia
Language: English (Spanish)
Genre: Technology
Published (Last): 12 June 2013
Pages: 40
PDF File Size: 3.23 Mb
ePub File Size: 2.64 Mb
ISBN: 630-3-65232-608-6
Downloads: 48506
Price: Free* [*Free Regsitration Required]
Uploader: Akinojind

POK2 is high impedance when the output is in regulation and the soft-start circuit has terminated. Trade-offs in PFM noise vs light-load efficiency are made by varying the inductor value. Add some isl636 for the rise in rDS ON with temperature. POK1 is low in shutdown. POK1 is high impedance when the output is in regulation and the soft-start circuit has terminated.

No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. If the voltage falls too low, the converter may not be able to turn on UGATE when the output voltage falls to the reference. For example, use an MBR mA-rated type for loads up to 1. The actual peak current is greater than the current-limit threshold by an amount equal to the inductor ripple current. The internal digital soft-start timer begins to ramp up the maximum-allowed current limit during start-up.

This will refresh an external 14V charge pump without overcharging the output voltage. The high-side switch ON-time is determined by a one-shot whose period is inversely proportional to input voltage and directly proportional to output voltage.

LIR is the ratio of the peak-peak ripple current to the average inductor current. Low-current applications usually require less attention. When using low-capacity filter capacitors such as polymer types, capacitor size is usually determined by the capacity required to prevent VSAG and VSOAR from tripping the undervoltage and overvoltage fault latches during load transients in ultrasonic mode.

  ALM 12V7 PDF

Disabling the zero-crossing detector causes the low-side, gate-drive waveform to become the complement of the high-side, gate-drive waveform.

All Rights Reserved All other trademarks mentioned are the property of their respective owners. For information regarding Intersil Corporation and its products, see www.

This mechanism causes the threshold between pulse-skipping PFM and non-skipping PWM operation to coincide with the boundary between continuous and discontinuous inductor-current operation also known as the critical conduction point: Switching frequency increases as a function of load current due to the increasing drop across the synchronous rectifier, which causes a faster inductor-current discharge ramp.

Another one-shot sets a minimum OFF-time ns typ. VREF3 can supply up to 5mA for external loads. The ISL includes an adjustable low drop-out linear regulator.

These factors include the internal gate resistance, gate charge, threshold voltage, source inductance, and PC board layout characteristics. RF interference in sensitive datsheet. VDROP2 is the sum of the parasitic voltage drops in the charging path, including high-side switch, inductor, and PC board resistances? Other features include pulse skipping, which maximizes efficiency in light-load applications, and fixed-frequency PWM mode, which reduces RF interference in sensitive applications.

UVP is ignored for at least 20ms typicalafter start-up or after a rising edge on EN. Do not operate at or near the maximum ratings listed for extended periods of time. LDO can provide a total of mA external loads.

Connect the top-side star ground used for MOSFET, input, and output capacitors to the small island with a single short, wide connection preferably just a via.

ISL Datasheet, PDF – Alldatasheet

These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. The boost capacitance should be as large as possible to prevent it from charging to excessive voltage, but small enough to adequately charge during the minimum low-side MOSFET conduction time, which happens at maximum operating duty cycle this occurs at minimum input voltage. Size and efficiency trade-offs must be considered when setting the inductor ripple current ratio. Connect BYP to 3.

  AQEEDATUL WAASITIYYAH ARABIC PDF

The ISL controller has a built-in 5? The current-limit threshold adjustment range is from 20mV to mV. Also, keep in mind that transient-response performance of buck regulators operated close to dropout is poor, and bulk output capacitance must often be added see Equation 11 on page The synchronous-switch gate drivers are directly powered from PVCC, while the high-side switch gate drivers are indirectly powered from PVCC through an external capacitor and an internal Schottky diode boost circuit.

High-Efficiency, Quad-Output, Main Power Supply Controllers For Notebook Computers

This interleaves the current pulses drawn by the two switches and reduces the overlap time where they add together. POK2 is low in shutdown. VREF3 can source up to 5mA for external loads. An ultrasonic pulse occurs when the controller detects that no switching has occurred within the last 20? F Q3b C4 0. Datadheet Controllers for Notebook. The actual capacitance value required relates to the physical size needed to achieve low ESR, datxsheet well as to the chemistry of the capacitor technology.

Output voltage control for SMPS2. The current datasheett varies with the ON-resistance of the synchronous rectifier. Ignoring the sag due to finite capacitance: C8 voltage is equal to OUT1 minus a datadheet drop. However, for high-current applications, some combinations of high- and low-side MOSFETs may cause excessive gate-drain coupling, which leads to poor efficiency and EMI-producing shoot-through currents.

These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. When trade-offs in trace lengths must be made, it is preferable to allow the inductor charging path to be made longer than the discharge path. Run the power plane ground currents on the top side only, if possible.