Changed layout of National Data Sheet to TI format. LevelC-UNLIM. to LMM. LMN. ACTIVE. PDIP. NFF. TBD. Call TI. Call TI. LMN Datasheet, LMN National Semiconductor Frequency to Voltage Converter Datasheet, buy LMN. LMN LM – Frequency to Voltage Converter, Package: Soic Narrow, Pin Nb= The LM Details, datasheet, quote on part number: LMN.

Author: Arashigis Nazuru
Country: Angola
Language: English (Spanish)
Genre: Science
Published (Last): 9 April 2005
Pages: 224
PDF File Size: 11.34 Mb
ePub File Size: 17.50 Mb
ISBN: 875-5-49646-637-1
Downloads: 38965
Price: Free* [*Free Regsitration Required]
Uploader: Nall

Click here to register now. This op-amp works as a sort of ‘trip amp’, whenever the input on pin 1 exceeds the voltage on pin 8 0vthe output to the charge pump will go high, being low at all other times.

Also, I need to be very conservative wrt adding components. Other than that you said the circuit worked, just gave the wrong rangethe diagram you posted is correct, the vaues should be OK.

LMN datasheet, Pinout ,application circuits Frequency To Voltage Converter

Electro Tech is an online community with overmembers who enjoy talking about and building electronic circuits, projects and gadgets. By continuing to use catasheet site, you are consenting to our use of cookies. That range can give me a larger range to have a more accuracy signal to do speed control. Can any professional give me a design which can achive a higher range of output, om2907n.

This version is well suited for single speed or frequency switching or fully buffered frequency to voltage conversion applications. Adding 2 more ics to do the trick is not an option. This version is well suited for single.


Forums New posts Search forums. The two basic configurations offered include an 8-pin device with a ground referenced tachometer input and an internal connection between the tachometer output and the op amp non-inverting input. As i read from d’sheet it can’t do this. I’m trying to sense the freq of a square wave from 10KHz – 40KHz range.

The more versatile configurations provide differential ta. But i want to know the accuracy of this circuit? You can then drive the transistor to give you an output of up to Vcc.

Or any other methods can achieve the task? Both of these configurations are available with an active. The 8 pin package dtaasheet the op-amp input stage’s inverting input connected to ground via pin 8the non-inverting input is on pin 1.

Both of these configurations are available with an active shunt regulator connected across the power leads.

LMN Datasheet(PDF) – National Semiconductor (TI)

The input signal must therefore go positive AND negative for the circuit to work. The tachom- eter uses a charge pump technique and offers frequency doubling for low ripple, full input protection in two versions LM, LM and its output swings to ground for a zero frequency input. Sorry, can anybody give me advice or the circuit is correct or any incorrect place? I have made the circuit but seem not work.

As I want to know the attached circuit is correct as what you mention? So, what can I do.


But I need 10khz to 40khz give me a 0 volt – Vcc variation. Replacement Transformer Started by ncag 47 minutes ago Replies: Sorry, can you give me any advice of which type can do such thing? Why not connect the output to a transistor base.

Now I understand the chip gives you a 0volts to Vcc variation for 0 Hz to fmax. LM, LM and its output swings to ground for a.

The IC has three basic sections, a trip amp, a charge datasheeh and an op amp, if the charge pump and following integrator can’t be set to the desired time constant then the op amp can give lots of gain. Don’t worry about calculating the R1,C1,C2 values.

Thank you for your reply.

Design Frequency to Voltage Circuit of LM2907N

But I still cannot be sucessful to make a larger voltage output range. This is important as the input signal MUST cross this zero volt threshold:!: BUT As the circuit will lose some voltage it will stop short of 12v out. Welcome to our site! LM – 8 pin package As you show the 8 pin package circuit, I assume this is what you have – there is a 14 pin version as well.

Thank you a lot.

Articles Top Articles Search resources. So, can you give me any advice about the accuracy of the circuit?